Macard RE 1200 Wifi Extender Setup: Bridge The Network Gap

Struggling with dead zones and weak wifi signals at your home? The Macard RE1200 is the ultimate fix for your problem. This device comes with an Ethernet port and WPS button for easy connectivity. Similarly, macard re 1200 wifi extender setup is the only way to use this networking device to its full potential. The ultra-broad antennas boost the network speed and signal strength.

In addition to this, the configuration of this advanced repeater can be carried out using the WPS button and web address. Likewise, to get more elaborative information on the macard re 1200 setup, walk through this detailed guide. You can explore the detailed steps for each procedure, among other information, so stay tuned!

Quick steps to execute the macard re 1200 wifi extender setup

Furthermore, the process of configuring the Macard repeater is quite simple. All you need to begin the process is an active internet connection, valid admin details, a web/IP address, a computer/smartphone, etc. After gathering all the necessary things, proceed with the steps mentioned below for macard re 1200 wifi extender setup:

Web GUI

Primarily, link your computer/laptop to the Macard extender’s network.
Now, access the web browser and write in go.macard.online web address or 192.168.10.1 IP address in the browser bar.
You can also use your smartphone for this purpose, but ensure to connect it to the extender network.
Here, a login window appears to you; enter the accurate username and password here.
After logging in, you land on the macard re 1200 wifi extender setup wizard.
Now, you see multiple options here; click on the WiFi Extender/Repeater only.
Afterward, choose your Time zone and opt for the 5Ghz/2.4GHz network frequency that you want to use.
At this point, the extender will scan for the available networks.

Join the router network

A list of the nearby networks is shown to you, so choose your home network from this list.
After that, key in the password for the chosen internet connection and tap on Next.
A new page will appear to you to give a new network name and password to your extender connection.
Otherwise, you can use the same details as your existing router has.
You need to recheck the information that you have entered and then click on the Save & Apply option.
Now, check the wifi LED on the repeater, if it is solid, then a connection is established successfully.
You can also configure the additional settings, like Guest Network, parental controls, etc., by following the on-screen instructions.
Here, your extender reboots itself and starts again.
At last, the macard re 1200 wifi extender setup ends effortlessly.

WPS Button

First & foremost, position the extender and the router within the same room.
Now, bring a sharp object, like a paper clip/pinpoint, etc., to press the button.
Next, look for the WPS knob on the router and the extender.
After that, press and hold this button on the router first and then on the extender within 2 minutes using a paper clip/pinpoint.
Wait until the WiFi LED on the repeater turns ON.
Now, let the buttons go off on the router and the extender.
Finally, the macard re 1200 setup process finishes successfully.

How to factory Reset Macard RE1200 extender?

Generally, users face issues while they perform the macard re 1200 wifi extender setup. Likewise, issues may appear due to an unstable network, signal barriers, using inaccurate admin details, etc.

However, if they are unable to fix the setup issues using other methods, then a hard reset is the only solution. Therefore, we have shed light on the Macard wifi extender factory reset steps in this section to assist them with this process:

Initially, confirm that your range extender is powered on.
Now, look for the reset button on it.
It is located on the side or at the bottom of the repeater.
Next, take a paper clip or pinpoint to press this tiny knob.
Similarly, hold it for 10-15 seconds until the lights on the extender start blinking, and then turn it off.
Now, wait for some time till the repeater power cycles itself and powers on again.
Lastly, the Macard RE1200 wifi extender reset ends.
Your repeater reverts to its default settings, and you have to reconfigure it from scratch.

In the end, this page sums up the detailed information regarding the macard re 1200 wifi extender setup. You can choose a web address or the WPS method to perform the extender setup along with the hard reset process if you encounter unfixed setup issues. Hope you find this guide helpful to set Macard repeater according to your preferences!